A bolt can have the correct diameter and still be completely wrong for the nut or threaded hole it needs to fit. One of the most common reasons is the thread.
UNC, UNF and Metric threads are widely used across engineering, manufacturing and construction, but they follow different sizing systems and pitches. Understanding the difference becomes particularly important when replacing old fasteners or specifying components for equipment built in different countries.
What Are UNC Threads?
UNC stands for Unified National Coarse. It belongs to the Unified inch thread system covered by ASME B1.1.
A UNC thread has fewer threads per inch than a UNF thread of the same nominal diameter. For example, a 1/2-13 UNC fastener has a nominal diameter of half an inch and 13 threads per inch.
The larger, deeper thread form makes UNC a common general-purpose choice. Coarse threads can be easier to start during assembly and may be more forgiving where threads are exposed to dirt, minor damage or frequent dismantling.
They can also be useful in some softer materials because the deeper thread provides substantial engagement with the surrounding material.
What Are UNF Threads?
UNF stands for Unified National Fine.
It uses the same inch-based Unified system as UNC, but places more threads within each inch. A 1/2-20 UNF fastener, for example, has the same nominal half-inch diameter as the previous UNC example, but has 20 threads per inch.
The smaller pitch creates a larger tensile stress area in a bolt of the same nominal diameter and can allow finer adjustment when tightening or positioning components. The exact performance still depends on factors including material, thread engagement and the load applied.
This is why UNC and UNF should not be treated as interchangeable simply because the outside diameter appears identical.
How Are Metric Threads Different?
Metric threads use millimetres rather than inches and are standardised through the ISO metric thread system. ISO 261 specifies the general plan for ISO metric screw threads, while ISO 724 defines their basic dimensions.
A designation such as M12 x 1.75 means the thread has a nominal diameter of 12mm and a pitch of 1.75mm.
Pitch is the distance from one thread crest to the next. This differs from the Unified system, where sizes are commonly described using threads per inch.
Metric threads also come in coarse and fine pitches. M12 x 1.75 is a commonly used coarse pitch, while an M12 fastener may also be produced with a finer pitch such as M12 x 1.25.
Canmec’s current thread range includes both Metric and Metric Fine alongside UNC and UNF options.
How Can You Tell Which Thread You Have?
Start by measuring the outside diameter of the male thread.
For Unified threads, a thread gauge can then be used to determine the number of threads per inch. A measurement of half an inch combined with 13 threads per inch would indicate 1/2-13 UNC, while 20 threads per inch would point towards 1/2-20 UNF.
Metric threads are measured differently. Check the outside diameter in millimetres and then measure the distance between adjacent thread crests.
Thread gauges make this considerably easier, particularly when the difference between two pitches is small.
Old machinery deserves extra care because equipment may contain Unified, Metric, BSW, BSF or other thread forms depending on its age and origin.
Can UNC, UNF and Metric Fasteners Be Interchanged?
Generally, no. A UNC nut will not correctly fit a UNF bolt of the same nominal diameter because the pitch is different. Metric and Unified components are also manufactured to different dimensional systems.
Occasionally two unrelated threads can appear to start fitting because their diameters and pitches happen to be relatively close. Continuing to tighten them can damage both components.
If a thread cannot be identified confidently, measuring it properly is preferable to forcing a seemingly suitable fastener into place.
Which Thread Type Should You Specify?
The correct choice depends on the equipment, material, operating conditions and applicable engineering standard.
Existing machinery will usually dictate the thread already in use. For new equipment, engineers may consider assembly requirements, available thread engagement, component strength and the standards followed across the wider system.
Canmec manufactures a range of thread forms including UNC, UNF, Metric, Metric Fine, UNEF, BSW, BSF and 8UN/UNS for different industrial requirements.
Correct identification matters because the thread is responsible for transferring load between connected components. Getting the diameter right is only half of the specification. The pitch and thread standard need to match as well.
FAQs
What Does UNC Stand For?
UNC stands for Unified National Coarse. It is an inch-based thread series with fewer threads per inch than the equivalent UNF size.
What Does UNF Stand For?
UNF stands for Unified National Fine. It uses more threads per inch than UNC for the same nominal fastener diameter.
What Does M12 x 1.75 Mean?
It describes a metric thread with a nominal diameter of 12mm and a distance of 1.75mm between adjacent thread crests.
Can a UNC Bolt Fit a UNF Nut?
No. Even when the nominal diameter is the same, the different thread pitches mean the components are not correctly compatible.
How Can I Identify an Unknown Bolt Thread?
Measure the outside diameter and use a thread pitch gauge. Unified threads are commonly identified by threads per inch, while metric threads are identified using pitch measured in millimetres.